Enamel microabrasion

Enamel microabrasion is a procedure in cosmetic dentistry used to improve the appearance of the teeth. Like tooth whitening it is used to remove discolorations of the tooth surface but microabrasion is a mechanical, rather than chemical, procedure.

History

In the past, teeth with stains or other color changes were made to look better through the use of restorative materials, such as dental porcelain. These materials would create a thin veneer over the outer surface of the tooth. Although veneers looked better, these materials did not match the structure or characteristics of the tooth enamel and replacement was frequently needed. As far back as 1916, some researchers were advocating instead removing a thin layer of the outermost enamel to expose the (presumably) undamaged layer underneath.<ref>,

 A technique for removal of fluorosis stains., 
 J Am Dent Assoc, 
 
 Vol. 109:63-64.,</ref>  The first practical application of enamel microabrasion was developed by Theodore Croll and Richard Cavanaugh in 1986, who used a combination of weak hydrochloric acid and pumice to remove a few tenths of millimeters of the enamel.<ref>, 
 Enamel color modification by controlled hydrochloric acid-pumice abrasion. I. technique and examples, 
 Quintessence Int., 
 
 Vol. 17(Issue: 2),
 pp. 81–7,
 
 PMID: 3457401,</ref><ref>, 
 Enamel color modification by controlled hydrochloric acid-pumice abrasion. II. Further examples., 
 Quintessence Int, 
 
 Vol. 17(Issue: 3),
 pp. 157–64,
 
 PMID: 3458266,</ref>

Description

Contemporary enamel microabrasion uses a combination of mechanical and chemical means to remove of a small amount of tooth enamel (not more than a few tenths of a millimeter) to eliminate superficial discoloration.<ref>

PRĒMA Enamel Microabrasion Compound(link). Premier Dental. Premier Dental.

</ref> These discolorations can result from either from extrinsic factors (such as tobacco, dental plaque, certain foods, etc.) or intrinsic ones (most commonly dental fluorosis).

Indications

• Dental fluorosis is the most common indication where it ranges in severity from mild to severe, microabrasion should be considered the first option in treating mild and moderate cases of fluorosis.<ref>,

 Clinical evaluation of enamel microabrasion for the aesthetic management of mild-to-severe dental fluorosis., 
 J Esthet Restor Dent, 
 
 Vol. 25(Issue: 6),
 pp. 422–30,
 DOI: 10.1111/jerd.12052,
 PMID: 24320061,</ref>

• Removal of intrinsic enamel stains, correction of surface irregularities and defects in enamel caused either after removal of orthodontic appliances or during tooth formation.<ref>,

 Enamel microabrasion to improve enamel surface texture, 
 J Esthet Dent, 
 
 Vol. 2:125-128.,</ref><ref>, 
 Enamel microabrasion for removal of superficial dysmineralization and decalcification defects, 
 J Am Dent Assoc,</ref>

Contraindications

• The patients' age is not a limiting factor for the enamel microabrasion technique but in cases of not fully erupted teeth, it may be difficult to place rubber dam for the microabrasion process<ref name=Sundfeld>,

 Smile restoration through use of enamel microabrasion associated with tooth bleaching, 
 Compend Contin Educ Dent, 
 
 Vol. 32(Issue: 3),
 pp. e53-7,
 
 PMID: 23738859,</ref>

• Microabrasion is not indicated when discoloration is located in dentin such as in dentigenous imperfecta or tetracycline discoloration.
• Should be delayed or not used in patients with deficient labial seal because enamel surfaces are extremely dry which makes stains more obvious.so, Sundfeld, et al in 2007, found that orthodontic lip repositioning should be done first to make removal of these stains more effective.<ref>,

 Considerations about enamel microabrasion after 18 years, 
 Am J Dent, 
 
 Vol. 20(Issue: 2),
 pp. 67–72,
 
 PMID: 17542197,</ref>

Consequences

Patients can benefit from combined microabrasion/ bleaching techniques as microabrasion causes reduction in the enamel surface and sometimes the tooth surface appear yellowish or darker due to exposure of dentin surface and thinning of enamel layer over it.In this condition, correction of this yellow color can be achieved by using tooth whitening technique to mask the color.<ref name=Sundfeld/>

Fragoso, et al. (2011) found that applying fluoride paste on enamel surface after microabrasion process provides higher hardness & more enamel smoothness.<ref>,

 Evaluation of physical properties of enamel after microabrasion, polishing, and storage in artificial saliva., 
 Biomed Mater, 
 
 Vol. 6(Issue: 3),
 pp. 035001,
 DOI: 10.1088/1748-6041/6/3/035001,
 PMID: 21487176,</ref> in addition, Segura et al found that  the treated enamel  surface become more resistant to demineralisation than untreated enamel and less colonisation of bacteria occur.<ref>, 
 Effect of enamel microabrasion on bacterial colonization, 
 Am J Dent, 
 
 Vol. 10(Issue: 6),
 pp. 272–4,
 
 PMID: 9590914,</ref>

References

   This article is a medical stub. You can help WikiMD by expanding it!